How to connect RGB Fans to Motherboard 2022

How to connect rgb fans to motherboard

How to connect RGB Fans to Motherboard. When it comes to communicating with someone, this may be straightforward, but many PC enthusiasts may be wary of some people. As a result, we educate you on how to obtain it.

The ability of a tower to effectively transmit heat from the inside to the outside is dependent on its ability to ventilate. If we don’t do this, the hot air will be trapped inside, where it might cause severe thermal throttling in the GPU, CPU, or M.2 SSD, among other things. Consequently, we will examine how to connect several PC fans, as well as what the tricks are to doing this task.

Ways to connect RGB fans to motherboard – How to connect RGB Fans to motherboard

Due to a large number of ports on the motherboard, the fact that the fan is connected does not create any problems. The problem arises when we wish to install many PC wings but only have four or fewer connectors available; therefore, we will look at some installation suggestions for PC wings.

Each fan is oriented in a different direction.

You should be aware that the fans only push air in one direction, therefore we must ensure that they are appropriately positioned in order to form a suitable air circuit inside the case. If you want to play a trick on yourself, look at the rear of the fan because there are typically some indicators indicating the direction the fan is pushing the air.

Why are there no arrows on the back? It is the manufacturer’s responsibility to explain this in the Fan Instruction Manual, as well as to include a reflection on how to set it up in the box if this does not occur. This is really crucial, especially if we intend to install a large number of fans in the computer casing.

Where to connect each fan

Most motherboards have four-pin connectors with the following specs, which we will describe below.

  • SYS FAN is an abbreviation for system or case fan.
  • CHA FAN is an abbreviation for case or chassis fan.
  • PWR FAN: Fan for the power supply (do not include it in this list).
  • CPU FAN is an abbreviation for CPU fan or processor heatsink fan.
  • AIO PUMP: For liquid cooling water blocks (also known as AIO).
  • EXT FAN is a 5 pin connector (which is uncommon) for a fan extension card.

Connect PC fans to SYS FAN and CHA FAN connectors whenever possible, especially if you plan to reprogram the computer later. If you purchase a fan extension card and you already have EXT FAN, you should connect it there.

Using a HUB adapter, you can attach extra fans.

Not uncommonly, many users have a huge box in which they can fit a large number of fans. This is not uncommon. You may discover that the four-pin CHA FAN or four-pin SYS FAN connectors on your motherboard are insufficient.

Relax, there is a solution, and it is a HUB adapter, which can output several 4-pin ports from a single 4-pin connector, allowing you to save space. Come on, you’ve been a lifelong adaptor. All of the positive news about this hub is due to the fact that:

  • They are really inexpensive.
  • The advantages they give are immeasurable.

Fan SATA adapter for SATA drives

To answer your question, you can attach numerous fans to the SATA connector, as you read. We rarely use more than two SATA 6Gb / s connections because we don’t often install a large number of solid-state drives. Even less so with the introduction of M.2 SSDs, which are pre-installed in a specific slot.

Finally, the utility is the same: it allows you to power several fans from a single socket. We will be able to power up to four more fans with a single connector in this manner. Of course, because the SATA connection is not commonly used for these purposes, this can present issues when reprogramming the device later on.

All fans are controlled from a central hub.

The user is normally preoccupied with connecting and running all of the wings on the computer, but what about controlling them? Noctua and Corsair, on the other hand, have their own HUBs, which work as a switchboard, connecting all of the fans together and allowing the user to operate them all without any fuss.

We believe that purchasing these HUBs is highly recommended if you have multiple fans from the same manufacturer, such as Corsair. The HUB from the American company stimulates its ecology, since it is capable of harmonizing the light from all Corsair fans when used in conjunction with other Corsair fans.

As a result, not only is it beneficial to set the ventilation curves, but it is also beneficial to have a synchronous light in the box.

Purchase 140mm fans.

If the PC chassis permits us to attach a 140 mm fan, we strongly propose that we do so because it will considerably boost the cooling capacity of the system (as long as the air flow, RPM and static pressure parameters are followed). (It must be completed.)

As a result, we would not be limited to a maximum of 120mm wings, which would alleviate the problem of not having enough connectors on the motherboard. As an illustration:

  • 6 Install 120mm fans on the ceiling (3 front – 3 top).
  • 4 x 140 mm fans should be installed (2 front – 2 top).

Conclusion

We’d want to leave you with some sound advice for the sake of your fans’ long-term well-being. To keep them from vibrating or “loosening,” it appears that we tighten the screws as much as possible when we install them.

If you tighten the screws too much, they’ll eventually need to be cleaned. So, we’d rather you not do that. Open them and clean them on the table so that you may work more comfortably.

With the passage of time, cells containing materials that shrink when heated or subjected to extreme conditions have been discovered. It can be difficult to open the fan if you squeeze it too hard during the day.

Leave a Comment

Your email address will not be published.

Scroll to Top